Product Code: RZ-UDZ Product Name: RZ-UDZ magnetic sub-level gauge Category: magnetic sub-level gauge magnetic sub-level gauge PP material http://www.harzkj.com/ywyb/cifuziyeweiji/2014/1215/ 390.html remote magnetic sub-level gauge http://www.harzkj.com/ywyb/cifuziyeweiji/2014/1214/362.html temperature magnetic sub-level gauge http://www.harzkj.com/ywyb/cifuziyeweiji /2014/1214/363.html side-mounted magnetic sub-level gauge http://www.harzkj.com/ywyb/cifuziyeweiji/2014/1215/386.html UHZ magnetic sub-level gauge http: //www.harzkj. com / ywyb / cifuziyeweiji / 2014/1215 / 388.html remote type magnetic float type level gauge http://www.harzkj.com/ywyb/cifuziyeweiji/2014/1215/389.html magnetic sub-level gauge corrosion http://www.harzkj.com/ywyb/cifuziyeweiji/2014/1216/397.html magnetic sub-level gauge Overview: RZ-UDZ magnetic sub-level gauge is based on the float magnet drive reversal color sheet to indicate fluid Bit of a new instrument. Within the body with the level of magnetic sub-movements up and down movement, while driving outside the main indicator color flakes inside flip, turn red when showing the level, turn black when there is no level is shown. Red and black ribbon, which represents the boundaries of the liquid level. On the left side with a striking indicator of the scale. So that the level of instruction is even more clear. Magnetic level gauge magnetic sub-level gauge Scope: magnetic sub-level gauge is the most common side-mounted magnetic sub-level gauge for working pressure of less than 2.5 MPa, the working temperature of 200 ℃ lower than the liquid medium level measurement. Universal magnetic sub-level gauge for the level of liquid in the container, the interface level measurement, in addition to on-site instruction, but also with a remote transmitter, alarm (control) switch, indicating functional. Indicates new, intuitive readings, eye-catching, observing the direction indicator to change the angle according to user needs. Measurement range, from tank height restrictions, indicating mechanism with the measured medium completely isolated, and thus a good sealing, high reliability and safety. Simple structure, easy installation, low maintenance costs. The basic difference between the number of magnetic sub-level gauge: Measuring range LD: 200 ~ 15000mm L1: the proportion of medium and float material related to the proportion of the table below medium L1 (mm) anti-rust aluminum float (LF2) and LF2 Fluorine wrapped in stainless steel float float (1Cr18ni9Ti) 0.45 463 0.55 286 0.65 210 0.75 166 0.85 140 340 0.95 120 260 ≤1.0 113 220 D: ￠ 52 ~ ￠ 83: ￠ 115 ~ ￠ 200 (depending on the pressure may be) Accuracy: ± 10mm medium temperature: ≤80 ℃, can also be made into a medium weight ≤480 ℃: ≥0.4 medium viscosity: ≤0.02Pa · S Flange: DN20 PN (MPa) 0.6 ~ 2.5 4.0 ~ 16.0 Standard HG20593-97 HG20595-97 Dg15 Pg (Kgf / cm2) 220 320 Standard H12-0-2 H12-0-3 Note: HG20595-97 I plant selection FM magnetic sub-level gauge gauge face when installing affected by the environment. Spatial location L1 <300, should be made clear orders. RZ-UDZ-3 remote magnetic sub-level gauge / B intrinsically safe by the body, magnetic sub, sensors, transmitters and flap indicator of five parts. Its working principle is based on magnetic float within the body while lifting with the level of pull reed on the corresponding position of the sensor. So that the total resistance (or voltage) within the sensor corresponding changes, and then through the transmitter converts the resistance (or voltage) is changed to 4 ~ 20mA · DC standard current output, then by supporting the production of our factory specialized XMT Series digital level controller is displayed on the level and set the lower limit alarm, to achieve the level of digital control or regulation. Also with my factory production XMGA supporting beam digital display regulator, display more intuitive. Or you can accept any other displays or regulator 4 ~ 20Ma · DC signal input matching, to achieve the level of the remote display, position control, intermittent or continuous PID regulator. The basic difference between the number: Ambient temperature: -10 ~ 50 ℃ medium temperature: ≤80 ℃, can also be made into ≤480 ℃ Output signal: 4 ~ 20mA · DC power supply: 24V · DC ± 5% Accuracy: L = 500 ~ 1000mm≤ ± 1.5% FS L> 1000 mm≤ ± 1.0% FS Load Resistance: 0 to 750 ohms proof mark: ibIICT5 remaining difference between the number and SSR-UDZ-1 magnetic sub-level gauge RZ-UDZ same type magnetic sub-level gauge specific categories: 1, RZ-UDZ-1D, HR-UDZ-3D / B insert magnetic float type level gauge: This gauge is suitable for underground tank, tank level measurement and control. 2, RZ-UDZ-1W, HR-UDZ-3W / B insulation type magnetic float level gauge: This gauge is to install an insulation jacket outside the main base type, etc., constitute steaming hot vehicle. Can be maintained within the normal flow of body fluid. So easy to apply to the solidification of the liquid level measurement and control. For low boiling point liquid refrigerant can pass into the cold water, etc. agent, in order to ensure the level of stability. The instrument correctly indicate the measured level. 3, RZ-UDZ-1S, HR-UDZ-3S / B frost magnetic float type level gauge: I plant designed to solve a cryogenic liquid level gauge outside icing design patent products. Insulation jacket is a vacuum layer. Thus can effectively isolate the cold, heat conduction. To ensure that the main gauge of the outer tube will not freeze, frost. Thus ensuring a level gauge of normal use. 4, RZ-UDZ-1J, HR-UDZ-3J / B resistant to corrosion magnetic float type level gauge: This gauge all wetted parts are made of plastic composite pipe. All can be applied to liquid level measurement and control of various highly corrosive media. 5, UDZ-1 type except local display level, it can also be equipped with type I plant XQ sender. It can be installed in UDZ-1 type level gauge body on the outside of the corresponding position on the lower level alarm, when the subject within the magnetic sub-level elevator moves up and down with the alarm set point, the magnet inside the float will allow within the sender reed contact closure or disconnect. Because the sender uses the principle of magnetic circuit memory. So contact signal output has self-holding function, which is not afraid of a power outage. After restoration. Sender contacts working condition still accurately reflect the real situation of the measured medium level, which is to ensure the safe operation of the production process technology plays a very important role. I plant supporting the use of SSR-XMTA series alarm controller can achieve the level of automatic control bits.